Watch the price of the Oneup EDC
|
From £14.00
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:318286
TheOneUp EDC Gear Straps are a stretch polyurethane strap with tail clip for neat and secure fastening of your spare tube or gear to your frame. This strap doesn’t absorb water and mud like a Velcro strap and won’t scratch your frame.OneUp EDC Gear Straps FeaturesKit includes 2x EDC gear strapsMaterial: UV Stabilized PolyurethaneWeight: 18g per strapLength: 355mm (14)""
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:325688
The OneUp Components EDC Stem Spacer and Bolt Kit allows you to dial in your OneUp everyday carry cockpit, with up to 30mm of stack adjustability. OneUp Components EDC Stem Spacer and Bolt Kit Features 4x M5x0.8x15mm Socket Head Cap Screws 2x M6x1x16mm Socket Head Cap Screws 2x 5mm EDC Stem headset spacers 2x 10mm EDC Stem headset spacers 1x preload lock nut 1x preload screw"
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:318266
The OneUp EDC Top Cap Kit includes the worlds lightest headset top cap (4.2g), and an EDC steerer plug with drain hole which keeps crud out of your steerer. Top caps are compatible with all 1-1/8 aluminum steerer tubes. The EDC steerer plug is required for EDC tool storage and is compatible with most aluminum tapered steerer tubes. OneUp EDC Top Cap Kit Features EDC TOP CAP EDC steerer plug 2x 1mm, 3mm, & 5mm Headset Spacers INSTALL THE EDC TOP CAP You need a minimum of 5mm of headset spacer above the stem and your steerer tube should be 1-2mm below the top of this spacer. Apply a small amount of grease to your newly cut thread and screw in your new EDC top cap. The Top Cap interface uses a standard cassette lockring tool. You do not need to apply much torque as you are only preloading the bearings. (Your stem pinch bolts are what holds your fork in place). The EDC multitool contains a top cap tightening tool. So even when riding you always have the ability to tighten your headset if need be. Align your stem and tighten your stem bolts to the manufacturers recommended torque. The final step is to insert the plastic bung/plug into the bottom of your fork. Turn your 8mm hex sideways and use it to push the plug into the fork by pulling the 8mm towards your chest. This piece holds the bottom of the EDC Tool and stops it from rattling. It also keeps dirt out of your fork and has a small drain hole."
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:318302
The OneUp EDC Top Cap Kit includes the worlds lightest headset top cap (4.2g), and an EDC steerer plug with drain hole which keeps crud out of your steerer. Top caps are compatible with all 1-1/8 aluminum steerer tubes. The EDC steerer plug is required for EDC tool storage and is compatible with most aluminum tapered steerer tubes. OneUp EDC Top Cap Kit Features EDC TOP CAP EDC steerer plug 2x 1mm, 3mm, & 5mm Headset Spacers INSTALL THE EDC TOP CAP You need a minimum of 5mm of headset spacer above the stem and your steerer tube should be 1-2mm below the top of this spacer. Apply a small amount of grease to your newly cut thread and screw in your new EDC top cap. The Top Cap interface uses a standard cassette lockring tool. You do not need to apply much torque as you are only preloading the bearings. (Your stem pinch bolts are what holds your fork in place). The EDC multitool contains a top cap tightening tool. So even when riding you always have the ability to tighten your headset if need be. Align your stem and tighten your stem bolts to the manufacturers recommended torque. The final step is to insert the plastic bung/plug into the bottom of your fork. Turn your 8mm hex sideways and use it to push the plug into the fork by pulling the 8mm towards your chest. This piece holds the bottom of the EDC Tool and stops it from rattling. It also keeps dirt out of your fork and has a small drain hole."
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:318232
The OneUp EDC Top Cap Kit includes the worlds lightest headset top cap (4.2g), and an EDC steerer plug with drain hole which keeps crud out of your steerer. Top caps are compatible with all 1-1/8 aluminum steerer tubes. The EDC steerer plug is required for EDC tool storage and is compatible with most aluminum tapered steerer tubes. OneUp EDC Top Cap Kit Features EDC TOP CAP EDC steerer plug 2x 1mm, 3mm, & 5mm Headset Spacers INSTALL THE EDC TOP CAP You need a minimum of 5mm of headset spacer above the stem and your steerer tube should be 1-2mm below the top of this spacer. Apply a small amount of grease to your newly cut thread and screw in your new EDC top cap. The Top Cap interface uses a standard cassette lockring tool. You do not need to apply much torque as you are only preloading the bearings. (Your stem pinch bolts are what holds your fork in place). The EDC multitool contains a top cap tightening tool. So even when riding you always have the ability to tighten your headset if need be. Align your stem and tighten your stem bolts to the manufacturers recommended torque. The final step is to insert the plastic bung/plug into the bottom of your fork. Turn your 8mm hex sideways and use it to push the plug into the fork by pulling the 8mm towards your chest. This piece holds the bottom of the EDC Tool and stops it from rattling. It also keeps dirt out of your fork and has a small drain hole."
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:318246
The OneUp EDC Top Cap Kit includes the worlds lightest headset top cap (4.2g), and an EDC steerer plug with drain hole which keeps crud out of your steerer. Top caps are compatible with all 1-1/8 aluminum steerer tubes. The EDC steerer plug is required for EDC tool storage and is compatible with most aluminum tapered steerer tubes. OneUp EDC Top Cap Kit Features EDC TOP CAP EDC steerer plug 2x 1mm, 3mm, & 5mm Headset Spacers INSTALL THE EDC TOP CAP You need a minimum of 5mm of headset spacer above the stem and your steerer tube should be 1-2mm below the top of this spacer. Apply a small amount of grease to your newly cut thread and screw in your new EDC top cap. The Top Cap interface uses a standard cassette lockring tool. You do not need to apply much torque as you are only preloading the bearings. (Your stem pinch bolts are what holds your fork in place). The EDC multitool contains a top cap tightening tool. So even when riding you always have the ability to tighten your headset if need be. Align your stem and tighten your stem bolts to the manufacturers recommended torque. The final step is to insert the plastic bung/plug into the bottom of your fork. Turn your 8mm hex sideways and use it to push the plug into the fork by pulling the 8mm towards your chest. This piece holds the bottom of the EDC Tool and stops it from rattling. It also keeps dirt out of your fork and has a small drain hole."
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:318340
The OneUp EDC Top Cap Kit includes the worlds lightest headset top cap (4.2g), and an EDC steerer plug with drain hole which keeps crud out of your steerer. Top caps are compatible with all 1-1/8 aluminum steerer tubes. The EDC steerer plug is required for EDC tool storage and is compatible with most aluminum tapered steerer tubes. OneUp EDC Top Cap Kit Features EDC TOP CAP EDC steerer plug 2x 1mm, 3mm, & 5mm Headset Spacers INSTALL THE EDC TOP CAP You need a minimum of 5mm of headset spacer above the stem and your steerer tube should be 1-2mm below the top of this spacer. Apply a small amount of grease to your newly cut thread and screw in your new EDC top cap. The Top Cap interface uses a standard cassette lockring tool. You do not need to apply much torque as you are only preloading the bearings. (Your stem pinch bolts are what holds your fork in place). The EDC multitool contains a top cap tightening tool. So even when riding you always have the ability to tighten your headset if need be. Align your stem and tighten your stem bolts to the manufacturers recommended torque. The final step is to insert the plastic bung/plug into the bottom of your fork. Turn your 8mm hex sideways and use it to push the plug into the fork by pulling the 8mm towards your chest. This piece holds the bottom of the EDC Tool and stops it from rattling. It also keeps dirt out of your fork and has a small drain hole."
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:318344
The OneUp EDC Top Cap Kit includes the worlds lightest headset top cap (4.2g), and an EDC steerer plug with drain hole which keeps crud out of your steerer. Top caps are compatible with all 1-1/8 aluminum steerer tubes. The EDC steerer plug is required for EDC tool storage and is compatible with most aluminum tapered steerer tubes. OneUp EDC Top Cap Kit Features EDC TOP CAP EDC steerer plug 2x 1mm, 3mm, & 5mm Headset Spacers INSTALL THE EDC TOP CAP You need a minimum of 5mm of headset spacer above the stem and your steerer tube should be 1-2mm below the top of this spacer. Apply a small amount of grease to your newly cut thread and screw in your new EDC top cap. The Top Cap interface uses a standard cassette lockring tool. You do not need to apply much torque as you are only preloading the bearings. (Your stem pinch bolts are what holds your fork in place). The EDC multitool contains a top cap tightening tool. So even when riding you always have the ability to tighten your headset if need be. Align your stem and tighten your stem bolts to the manufacturers recommended torque. The final step is to insert the plastic bung/plug into the bottom of your fork. Turn your 8mm hex sideways and use it to push the plug into the fork by pulling the 8mm towards your chest. This piece holds the bottom of the EDC Tool and stops it from rattling. It also keeps dirt out of your fork and has a small drain hole."
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:325687
The One Up EDC Stem Cap/Preload Kit includes an EDC ready headset top cap, a headset bearing preload assembly, 40mm of integrated headset spacers, and an EDC steerer plug. When installed into the OneUp Stem it creates an EDC ready stem that does not require threading your steerer tube. The OneUp Stem has a recess in the bottom of the body to house the Preloader assembly with a third bolt at the steerer clamp which you use to adjust the preload. Tightening the Preload Bolt on the back of the stem pulls the collar together, which tightens the internal cone and pushes the conical headset spacer down away from the stem and preloads your headset. One Up EDC Stem Cap/Preload Kit Features Stem EDC Top Cap EDC steerer plug Stem Preload assembly 2x 10mm, 2x 5mm, clip in headset spacers"
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:325689
The One Up EDC Stem Cap/Preload Kit includes an EDC ready headset top cap, a headset bearing preload assembly, 40mm of integrated headset spacers, and an EDC steerer plug. When installed into the OneUp Stem it creates an EDC ready stem that does not require threading your steerer tube. The OneUp Stem has a recess in the bottom of the body to house the Preloader assembly with a third bolt at the steerer clamp which you use to adjust the preload. Tightening the Preload Bolt on the back of the stem pulls the collar together, which tightens the internal cone and pushes the conical headset spacer down away from the stem and preloads your headset. One Up EDC Stem Cap/Preload Kit Features Stem EDC Top Cap EDC steerer plug Stem Preload assembly 2x 10mm, 2x 5mm, clip in headset spacers"
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:325691
The One Up EDC Stem Cap/Preload Kit includes an EDC ready headset top cap, a headset bearing preload assembly, 40mm of integrated headset spacers, and an EDC steerer plug. When installed into the OneUp Stem it creates an EDC ready stem that does not require threading your steerer tube. The OneUp Stem has a recess in the bottom of the body to house the Preloader assembly with a third bolt at the steerer clamp which you use to adjust the preload. Tightening the Preload Bolt on the back of the stem pulls the collar together, which tightens the internal cone and pushes the conical headset spacer down away from the stem and preloads your headset. One Up EDC Stem Cap/Preload Kit Features Stem EDC Top Cap EDC steerer plug Stem Preload assembly 2x 10mm, 2x 5mm, clip in headset spacers"
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:325692
The One Up EDC Stem Cap/Preload Kit includes an EDC ready headset top cap, a headset bearing preload assembly, 40mm of integrated headset spacers, and an EDC steerer plug. When installed into the OneUp Stem it creates an EDC ready stem that does not require threading your steerer tube. The OneUp Stem has a recess in the bottom of the body to house the Preloader assembly with a third bolt at the steerer clamp which you use to adjust the preload. Tightening the Preload Bolt on the back of the stem pulls the collar together, which tightens the internal cone and pushes the conical headset spacer down away from the stem and preloads your headset. One Up EDC Stem Cap/Preload Kit Features Stem EDC Top Cap EDC steerer plug Stem Preload assembly 2x 10mm, 2x 5mm, clip in headset spacers"
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:325695
The One Up EDC Stem Cap/Preload Kit includes an EDC ready headset top cap, a headset bearing preload assembly, 40mm of integrated headset spacers, and an EDC steerer plug. When installed into the OneUp Stem it creates an EDC ready stem that does not require threading your steerer tube. The OneUp Stem has a recess in the bottom of the body to house the Preloader assembly with a third bolt at the steerer clamp which you use to adjust the preload. Tightening the Preload Bolt on the back of the stem pulls the collar together, which tightens the internal cone and pushes the conical headset spacer down away from the stem and preloads your headset. One Up EDC Stem Cap/Preload Kit Features Stem EDC Top Cap EDC steerer plug Stem Preload assembly 2x 10mm, 2x 5mm, clip in headset spacers"
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:325696
The One Up EDC Stem Cap/Preload Kit includes an EDC ready headset top cap, a headset bearing preload assembly, 40mm of integrated headset spacers, and an EDC steerer plug. When installed into the OneUp Stem it creates an EDC ready stem that does not require threading your steerer tube. The OneUp Stem has a recess in the bottom of the body to house the Preloader assembly with a third bolt at the steerer clamp which you use to adjust the preload. Tightening the Preload Bolt on the back of the stem pulls the collar together, which tightens the internal cone and pushes the conical headset spacer down away from the stem and preloads your headset. One Up EDC Stem Cap/Preload Kit Features Stem EDC Top Cap EDC steerer plug Stem Preload assembly 2x 10mm, 2x 5mm, clip in headset spacers"
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:325698
The One Up EDC Stem Cap/Preload Kit includes an EDC ready headset top cap, a headset bearing preload assembly, 40mm of integrated headset spacers, and an EDC steerer plug. When installed into the OneUp Stem it creates an EDC ready stem that does not require threading your steerer tube. The OneUp Stem has a recess in the bottom of the body to house the Preloader assembly with a third bolt at the steerer clamp which you use to adjust the preload. Tightening the Preload Bolt on the back of the stem pulls the collar together, which tightens the internal cone and pushes the conical headset spacer down away from the stem and preloads your headset. One Up EDC Stem Cap/Preload Kit Features Stem EDC Top Cap EDC steerer plug Stem Preload assembly 2x 10mm, 2x 5mm, clip in headset spacers"
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:318245
The OneUp EDC Plug Plier Kit is the perfect addition to the EDC tool system. The tyre plug Jabber Tool threads directly into the EDC carrier (SOLD SEPARATELY). The new Quick Link Breaker Pliers are compatible with all 10,11, and 12 speed quick links chains. Both new tools and bacon strips store perfectly within the EDC capsule ready for race day deployment.OneUp EDC Plug Plier Kit FeaturesQuick Link Breaker Pliers (10, 11, 12SP)Tire Plug Jabber Tool15- Bacon StripsMaterial: Aluminium/SteelWeight: 17gCompatible with EDC tool systemThe complete Plug and Pliers kit fits inside the Stash Capsule of the 100cc Pump and Steerer tube setup. The Stash capsule does NOT fit inside the 70cc pump. You cannot store the pliers in the 70cc Pump. Although the Jabber and Tubeless plugs will fit inside."
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:318284
The OneUp EDC Tap Kit lets you remove your old star-nut and tap the top of your steerer tube. This might sound daunting, but they've made it super easy to do on your bike, without even removing your fork.OneUp EDC Tap FeaturesRemove your bar and stemUse the OneUp star-nut puller to remove your old star nutUsing the self-aligning steerer tap kit, tap a thread into your steerer until the tap bottoms out.Please see the video above and detailed instructions below. Please read entire instructions and consult your local bike shop if you are uncomfortable with performing the tapping procedure.OneUp EDC Tap InstructionsREMOVE YOUR STAR NUTPut your bike in a stand with the front wheel resting on the floor. If you don't have a bike stand, ensure that your bike is securely supported.Remove your top cap, top cap/headset spacers, stem and handlebar leaving at least 40mm of the exposed steerer.This would be a good time to shorten your steerer tube if you have an excess length above your stem. We recommend 5-10mm of steerer above the stem.Apply some grease to the inside of your steerer tube to make it easier to pull out your Star NutTake the OneUp Star Nut Puller (short silver cylinder) and drop it over your steerer tubeUsing a 5mm hex, tighten the supplied star nut puller bolt to pull the star nut out of your steerer.Your star nut will either pull out as complete piece or the centre portion of the star nut will pull out leaving 2 star-shaped pieces still in the steerer tube. If this happens, take a screwdriver and lightly tap one edge of the top star nut until it flips 90 degs and is easy to remove. Repeat for the second piece.THREAD YOUR STEERERPush a paper towel into the bottom of your steerer to plug the bottom of your fork. This protects your fork seals and stanchions from any aluminium chips created when you thread the steerer.Take the tap (threaded cutter piece) and put it inside the tap guide (long black tube piece), then take an 8mm Hex and push it through the hole in the tap that protrudes through the guide, this becomes your tap handle (think handle for turning a faucet).Grease the inside of the steerer, this makes it easier to cut the threads and will also help catch any falling chips.Place the tap assembly onto your steerer. The tap guide will automatically align the tap.To thread your steerer, turn the tap in the guide using the tap handle. 1/2 turn forward and 1/4 turn back, then repeatAfter 4 full turns, pour some chain lube or cutting fluid down one of the channels in your tap, this will make cutting the threads easier. Repeat this again after 8 turns of the tap.When you have threaded the full 8mm, the Tap Handle will bottom out on the guide and you will be unable to turn any further. The guide ensures you only ever tap to the exact depth necessary.Once you've bottomed out the tap, turn the tap handle counter-clockwise until the tap is free.Before removing the tap and guide assembly, wrap a paper towel around the top of your steerer to catch any chips that fall off the tap as you remove it.Hold a plastic bag under the steerer tube to catch any chips or debris. Take another paper towel and push it down through your newly threaded steerer using the 8mm hex. This removes all chips and pushes out the first towel you used to plug the steerer in Step #2.Reinstall your lower headset spacers and put your stem back on. Do not tighten your stem bolts yet.The OneUp EDC Tap Kit includes: A Star Nut Puller / Go No-Go" Gauge, Tap and Tap Guide. (A Tap is a common cutting tool used to manufacture/cut internal threads)""
-
Out of stock since 2020-11-05 12:29:11.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:318310
The OneUp EDC Tool System give you all the trailside tools you need, always on your bike and instantly accessible. Given the choice, we always prefer to ride without a backpack. But no one wants to be 'that guy' who needs to borrow tools, or be left walking home while your friends enjoy the rest of the ride. We wanted a solution that would allow us to carry the essential tools that we need for every ride, without wearing a bulky backpack. EDC stores your essential trail tools inside your steerer tube, right at your fingertips. Whether you're going out for a quick lunch ride or setting off on a longer adventure, EDC has all the tools that you need to keep your bike running smoothly and fix any trailside mechanical. The EDC tool can also be stored in our new high volume, CNC Alu Pump, which has an integrated CO2 inflator head. Grabbing your EDC tool from the pump is as easy as reaching for your water bottle. Please note, to fit the EDC Tool System, you'll need a threaded steerer & EDC Top Cap (1C0414BLK). You can thread your steerer with the EDC Tap Kit (1C0416BLK). OneUp EDC Tool System Features 2.5, 3, 4, 5, 6, 8mm Hex T25 Torx Tire Lever, Chain Breaker Spare Quick Link Storage Flat Head Screwdriver 0,1,2,3 Spoke Keys Presta Valve Core Tool EDC Top Cap Tool Spare Chainring Bolt Sealed Storage Capsule or 12,16, 20g CO2 Cartridge Storage "
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:318261
TheOneUp EDC Pump 100cc offers a unique storage solution integrated into a high volume pump. It is designed to integrate with the EDC Tool System, CO2 canister or your favourite stash. Crafted from aluminium with a durable textured machined finish. A mini pump might look appealing, but with typical volumes of 30-60cc, it will take hundreds of strokes to inflate a new tube and has absolutely no chance of re-inflating a tubeless setup. When you get a flat, you want to fix it as fast as possible as riding time is precious. At 100cc and at 160g One Up's high volume pump has the highest volume to weight ratio on the market.Firmly push the pump head onto the Presta valve until it bottoms out, then pump. With the fast-on head, the valve stem is securely supported so there's no chance of bending, breaking or unseating the valve and no chance of unscrewing your valve core when you remove the pump.OneUp EDC Pump 100cc FeaturesHigh Volume 100cc100cc Pump holds EDC Tool & a 20g CO2 or EDC Tool & the Storage CapsuleFast-On Head (Presta Only) - No threads or locking leversIntegrated CO2 InflatorFully Sealed, Weatherproofed InternalsIncludes Bottle Cage MountEDC sold separately"
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:318311
TheOne Up EDC Pump 70cc offers a unique storage solution integrated into a high volume pump. It is designed to integrate with the EDC Tool System, CO2 canister or your favourite stash. Crafted from aluminium with a durable textured machined finish. A mini pump might look appealing, but with typical volumes of 30-60cc, it will take hundreds of strokes to inflate a new tube and has absolutely no chance of re-inflating a tubeless setup. When you get a flat, you want to fix it as fast as possible as riding time is precious. At 100cc and at 160g our high volume pump has the highest volume to weight ratio on the market.Firmly push the pump head onto the Presta valve until it bottoms out, then pump. With One Up's fast-on head, the valve stem is securely supported so there's no chance of bending, breaking or unseating the valve and no chance of unscrewing your valve core when you remove the pump.OneUp EDC Pump 70cc FeaturesHigh Volume 70cc70cc Pump holdsEDCTool & a 20g CO2orEDCTool & the Storage CapsuleFast-On Head (Presta Only) - No threads or locking leversIntegrated CO2 InflatorFully Sealed, Weatherproofed InternalsIncludes Bottle Cage MountEDC Sold Separately"
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:354796
The OneUp EDC V2 Tool System has all the tools that you need to keep your bike running smoothly and fix any trailside mechanical, whether you're going out for a quick lunch ride or setting off on a longer adventure.The OneUp EDC V2 Tool System now comes with a small and a large sealed storage capsule. The new small capsule is used to cover your jabber and preloaded bacon strip keeping it sticky for longer. The small capsule can be used with EDC Threaded options, it also allows you to use the EDC tool and tubeless plug kit inside the small OneUp 70cc EDC Pump. The large capsule only fits inside an EDC Threaded setup, OneUp EDC Stem or OneUp 100cc EDC Pump. The small capsule can be installed inside the large capsule for separating items.The OneUp EDC V2 Tool System can be stored inside your OneUp EDC Stem, steerer tube (click here to see OneUp's fork compatibility guide) or inside the OneUp EDC Pump. Storage within the steerer tube requires you to thread your steerer.OneUp EDC V2 Tool System FeaturesEasier to remove from your bike, with a lower friction design.Updated Chain Breaker is easier to use and has a steel body for increased durabilityStronger steel Spoke KeysBlack Multi-ToolTubeless plug jabber cover (Small storage capsule)20 functionsIncludes a 10 function Multi-Tool, Tire Lever and Chain Breaker.Weight: 130gOneUp Multitool Features10 Functions2, 2.5, 3, 4, 5, 6, 8mm, T25 Torx. Flat Head Screwdriver. EDC Top Cap ToolThe EDC Tool contains no loose, easy to lose driver bitsUltra compact and super lightweight.Weight: 58gOneUp Tyre Lever/Chain Breaker FeaturesTyre Lever, Chain Breaker, 0,1,2,3 Spoke Keys, Presta Valve Core Tool, Spare Rotor BoltOneUp Carrier FeaturesSpare Quick Link Storage12,16, 20g CO2 Cartridge Storage or 2 x Sealed Storage CapsulesOneUp EDC V2 Tool System Storage OptionsThe OneUp EDC V2 Tool was designed to be stored inside your compatible stem/steerer tube or inside the high volume, CNC Aluminum, OneUp EDC Pump with integrated CO2 inflator head. Grabbing your OneUp EDC V2 Tool from the pump is as easy as reaching for your water bottle.Backwards compatible with all OneUp EDC V1 Tool storage options."
-
Out of stock since 2022-07-15 11:29:53.0
(Price includes delivery charge of £0.00)
Leisure Lakes Bikes ref:326179
The One Up Stem can be used with a regular star nut and top cap like every other stem. It’s also compatible with existing threaded EDC top caps, for people who’ve already threaded their steerer tube. Or you can use the new OneUp Preloader (sold separately), which lets you store the EDC tool in your steerer without threading it.One Up Stem SpecificationsLength: 35mm (157g) 50mm (173g) / 35mm Dia. / 0° RiseColour: Black.Stack Height: 39mmBar Clamp Width: 55mmMaterial: 6061-T6 AluminumOne Up Stem InstructionsInstall bar. Top bar clamp bolts tighten down to stem body with no gap. Bottom bar clamp bolts will have a gap. Torque bolts to 6Nm.Install stem onto steerer, align and tighten top 2 steerer bolts (9Nm)."
|